Warning Sorry, you're using a web browser that is no longer supported. For the best experience please upgrade or visit the site on another browser.
Skip to content

P0136, P0137, & P0138 Codes: Bank 1 Downstream O2 Sensor or Circuit

Diagnostic trouble codes P0136, P0137, and P0138 all indicate an issue with the Bank 1, Sensor 2 oxygen sensor (also known as the O2 sensor) or its circuit. Sensor 2 is the downstream sensor, located after the catalytic converter, and it helps the engine’s computer monitor how well the converter is working. P0136 indicates a general malfunction in the sensor circuit, P0137 indicates the sensor voltage is too low, and P0138 means the voltage is too high.

On V-type engines, bank 1 refers to the side of the engine containing cylinder 1, while bank 2 is the opposite side. For inline engines with a single row of cylinders, all cylinders are on bank 1. The equivalent codes for bank 2, sensor 2 are P0156, P0157, and P0158.

P0136, P0137, and P0138 codes are often related to a failure in one of the following areas:

Some common symptoms of worn out brake pads include:

  • A worn, contaminated, or failing downstream O2 sensor
  • Damaged wiring, corroded connectors, or loose pins in the sensor circuit
  • Exhaust leaks near flanges or joints ahead of the sensor
  • Sensor heater circuit power or ground issues
  • Short or open circuits in the wiring harness
  • Catalytic converter or fuel system problems affecting oxygen levels

P0136, P0137, & P0138 Code Repair: Common Parts & Tools

Free Check Engine Light Testing at O’Reilly Auto Parts

The parts and tools needed to resolve these codes can vary depending on your vehicle’s make and model. If your Check Engine light is on, stop by any O’Reilly Auto Parts for free VeriScan Check Engine light testing. You’ll receive a detailed report with more information about your vehicle’s diagnostic trouble code, possible causes, and repair options. If you aren’t comfortable performing the repair yourself, we can recommend a professional shop or a Certified Auto Repair Service Center in your area to get the job done right. 

What Do DTC Codes P0136, P0137, & P0138 Mean?

OBD-II fault code P0136 means “O2 Sensor Circuit Malfunction (Bank 1, Sensor 2),” P0137 means “O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2),” and P0138 means “O2 Sensor Circuit High Voltage (Bank 1, Sensor 2).” This indicates your engine’s computer has detected a problem with the signal from the bank 1 downstream oxygen sensor.

A low voltage reading (P0137) is often caused by a lean fuel mixture, wiring problems, or a failing sensor. A high-voltage reading (P0138) is often caused by a rich fuel mixture, a short to power, or a sensor signal that’s stuck.

P0136, P0137, & P0138 OBD-II Code Symptoms

Because the downstream sensor mainly monitors the catalytic converter, many vehicles show few symptoms beyond the Check Engine light. When symptoms do appear, they’re often tied to the underlying cause, such as a fuel mixture problem, and can include:

  • A Check Engine light
  • Rough idle
  • Hesitation or surging
  • Poor gas mileage
  • A stronger exhaust or fuel smell, if the engine is running rich

Diagnosing a P0136, P0137, or P0138 Code Yourself

If you’re comfortable diagnosing the issue yourself, these steps can help narrow down the cause:

  • Start with a free O’Reilly VeriScan report, which can show related codes, like a P0420 catalyst efficiency code or misfire codes in the P0300 range.
  • Inspect the downstream O2 sensor connector and harness for corrosion, melted insulation, or chafing.
  • Check for exhaust leaks near the sensor and flanges.
  • Verify heater circuit power and ground before replacing any parts.

Can I Drive With a P0136, P0137, or P0138 Code?

In many cases, your vehicle will continue to drive normally, though some vehicles may limit performance to protect the emissions system. Even if you don’t notice any symptoms, diagnose and fix the problem as soon as possible, since a rich-running engine can damage your catalytic converter and lead to costly repairs. 

Frequently Asked Questions: Diagnostic Trouble Codes

What does DTC mean?

DTC stands for Diagnostic Trouble Code. Your vehicle’s onboard diagnostics (OBD) system generates these codes when it detects a problem with one of your vehicle’s systems, which is also what triggers your Check Engine light. DTC codes help explain what the issue is and where it’s located, so you can begin diagnosing it.

What are some of the most common Diagnostic Trouble Codes?

Some common Diagnostic Trouble Codes (DTCs) include:

Can I clear a DTC myself?

You can use an OBD-II code reader to scan and clear DTCs yourself, but this only temporarily turns off your Check Engine light. If the underlying issue hasn’t actually been fixed, the code and the light will reactivate. Visit your local O’Reilly Auto Parts for free VeriScan Check Engine light testing.

Additional Resources