Ultima 125 Amp Alternator - Remanufactured - R111558
MasterPro Chassis Tie Rod End - EV800457
BrakeBest Caliper Guide Pin Kit Front - 14264
Standard Ignition Fuel Injector Seal Kit - SK71
Product
Attributes
Warranty
Color
----
----
----
Blue, Brown
Diameter (in)
----
----
5/16 Inch
----
Fan Type
Internal
----
----
----
Material
----
----
Steel
Rubber
Polarity
Negative
----
----
----
Thread Size
----
----
M8-1.0
----
Length (in)
----
----
1-1/8, 2-5/8 Inch
----
Length (mm)
----
----
29mm, 66mm
----
Rotation Direction
Clockwise
----
----
----
Voltage Regulator Type
Internal
----
----
----
New Or Remanufactured
Remanufactured
----
----
----
Pulley Included
Yes
----
----
----
Dust Boot Included
----
No
----
----
Grease Fitting Included
----
No
----
----
Greaseable
----
Yes
----
----
Nuts Included
----
----
No
----
Washers Included
----
No
No
----
Shoulder Length (in)
----
----
1/4 Inch
----
Pulley Type
Decoupler
----
----
----
Head Size (in)
----
----
9/16 Inch
----
Head Size (mm)
----
----
14mm
----
Pulley Diameter (in)
2-3/16 Inch
----
----
----
Thread Length (in)
----
----
1/2 Inch
----
Thread Length (mm)
----
----
13mm
----
Regulator Type
Internal
----
----
----
Voltage (V)
12 Volt
----
----
----
Pulley Diameter (mm)
55mm
----
----
----
Dust Boots Included
----
----
No
----
Amperage (A)
125 Amp
----
----
----
Instructions Included
----
----
No
----
OE Manufacturer
Nippondenso
----
----
----
Pre-Greased
----
Yes
----
----
Number Of Bolts
----
----
2
----
Color/Finish
----
----
Gray
----
Sleeve Included
----
----
No
----
Castle Nut Included
----
No
----
----
Cotter Pin Included
----
No
----
----
Hardware Kit Included
----
----
----
No
Pintle Cap Included
----
----
----
No
Lock Nut Included
----
Yes
----
----
Lock Washer Included
----
No
----
----
Intake Manifold Upper Set Included
----
----
----
No
Number Of O-Rings
----
----
----
16
Oversized
----
----
No
----
Number Of Pulley Grooves
6
----
----
----
One Wire Capable
No
----
----
----
AC Tap
No
----
----
----
Brushless Design
No
----
----
----
Adjusting Sleeve Included
----
No
----
----
Lubricant Included
----
----
No
----
Pulley Belt Type
Serpentine
----
----
----
Number Of Sleeves
----
----
0
----
Cooling Method
Air
----
----
----
Rod End Thread Gender
----
Male
----
----
Rack End Thread Gender
----
Male
----
----
Number Of Covered Injectors
----
----
----
0
Nozzle Seal Included
----
----
----
No
Ball Stud Type
----
Threaded
----
----
Ball Stud Housing Material
----
High Strength Steel
----
----
Ball Stud Bearing Material
----
Polymer
----
----
Tie Rod End Type
----
Inner
----
----
Plug Clock Position
8:00
----
----
----
Caliper Bolt Head Type
----
----
Hex
----
O-Ring/Seal 1 Inside Diameter (in)
----
----
----
0.310 Inch
O-Ring/Seal 1 Inside Diameter (mm)
----
----
----
7.87mm
O-Ring/Seal 1 Outside Diameter (in)
----
----
----
0.580 Inch
O-Ring/Seal 1 Outside Diameter (mm)
----
----
----
14.73mm
O-Ring/Seal 2 Inside Diameter (in)
----
----
----
0.310 Inch
O-Ring/Seal 2 Inside Diameter (mm)
----
----
----
7.87mm
O-Ring/Seal 2 Outside Diameter (in)
----
----
----
0.580 Inch
O-Ring/Seal 2 Outside Diameter (mm)
----
----
----
14.73mm
O-Ring/Seal 2 Thickness (in)
----
----
----
0.140 Inch
O-Ring/Seal 2 Thickness (mm)
----
----
----
3.556mm
O-Ring/Seal 3 Inside Diameter (in)
----
----
----
0.370 Inch
O-Ring/Seal 3 Inside Diameter (mm)
----
----
----
9.39mm
O-Ring/Seal 3 Outside Diameter (in)
----
----
----
0.570 Inch
O-Ring/Seal 3 Outside Diameter (mm)
----
----
----
14.47mm
O-Ring/Seal 3 Thickness (in)
----
----
----
0.100 Inch
O-Ring/Seal 3 Thickness (mm)
----
----
----
2.54mm
O-Ring/Seal 4 Inside Diameter (in)
----
----
----
0.370 Inch
O-Ring/Seal 4 Inside Diameter (mm)
----
----
----
9.39mm
O-Ring/Seal 4 Outside Diameter (in)
----
----
----
0.570 Inch
O-Ring/Seal 4 Outside Diameter (mm)
----
----
----
14.47mm
O-Ring/Seal 4 Thickness (in)
----
----
----
0.100 Inch
O-Ring/Seal 4 Thickness (mm)
----
----
----
2.54mm