Dorman HELP! U-Joint Repair Kit - 81020
Precision Chassis Tie Rod End - EV800300
BrakeBest Brake Caliper - Remanufactured - 18-4601
NGK Copper Plug Number D8EA Spark Plug - 2120
Product
Attributes
Warranty
Color
----
----
Gray
----
Finish
----
----
Oil Emulsion
----
Material
Steel
----
----
----
Seat
----
----
----
Gasket
Thread Size
----
----
----
M12-1.25
Heat Range
----
----
----
8
Bracket Included
----
----
No
----
New Or Remanufactured
----
----
Remanufactured
----
Bleeder Screw Cap Included
----
----
No
----
Bleeder Screw Included
----
----
Yes
----
Hex Size (mm)
----
----
----
18mm
Dust Boot Included
----
No
----
----
Grease Fitting Included
----
No
----
----
Greaseable
----
No
----
----
Washers Included
----
No
----
----
Strap Width (in)
11/16, 11/16 Inch
----
----
----
Dust Boots Included
----
----
Yes
----
Pre-Greased
----
Yes
----
----
Number Of Pistons
----
----
1
----
Piston Material
----
----
Steel
----
Number Of Bolts
4
----
----
----
Preset Gap (in)
----
----
----
0.028 Inch
Preset Gap (mm)
----
----
----
0.7mm
Thread Reach (in)
----
----
----
0.750 Inch
Castle Nut Included
----
No
----
----
Cotter Pin Included
----
No
----
----
Lock Nut Included
----
No
----
----
Lock Washer Included
----
No
----
----
Casting Material
----
----
Cast Iron
----
Number Of Straps
2
----
----
----
Strap Length (in)
2-7/16, 2-1/8 Inch
----
----
----
Pads Included
----
----
No
----
Center Electrode Core Material
----
----
----
Copper
Center Electrode Tip Material
----
----
----
Nickel
Approximate Resistor Value (Ohm)
----
----
----
1000 Ohm
Insulator Height (mm)
----
----
----
50mm
Adjusting Sleeve Included
----
No
----
----
Piston Outside Diameter (in)
----
----
2.495 Inch
----
Piston Outside Diameter (mm)
----
----
63.373mm
----
Insulator Height (in)
----
----
----
1.970 Inch
Ground Electrode Tip Material
----
----
----
Nickel
Thread Reach (mm)
----
----
----
19mm
Rod End Thread Gender
----
Male
----
----
Rack End Thread Gender
----
Male
----
----
Ball Stud Type
----
Threaded
----
----
Ball Stud Housing Material
----
Steel
----
----
Ball Stud Bearing Material
----
Polymer
----
----
Caliper And Pad Hardware Included
----
----
Yes
----
Bracket Mounting Bolts Included
----
----
Yes
----
Bleeder Screw Thread (mm)
----
----
M10-1.50
----
Inlet Port Thread Size (in)
----
----
3/8 Inch
----
Inlet Port Thread Size (mm)
----
----
M10-1.50
----
Piston Inside Diameter (in)
----
----
2.055 Inch
----
Piston Inside Diameter (mm)
----
----
52mm
----
Service Number
----
----
----
D8EA
Metallurgy
----
----
----
Copper