MagnaFlow OEM Grade Direct-Fit Catalytic Converter - 21-476
Precision U-Joint - 905
MasterPro Chassis Tie Rod End - EV252
MasterPro Climate Control DKS20 A/C Compressor - Remanufactured - 167660
Attributes
Warranty
Oil Type
----
----
----
PAG 46
Series
OEM Grade
----
----
----
Hardware Included
No
----
----
----
New Or Remanufactured
----
----
----
Remanufactured
Substrate Material
Ceramic
----
----
----
Overall Length (in)
10-1/8 Inch
----
----
----
Overall Length (mm)
257mm
----
----
----
Dust Boot Included
----
----
No
----
Grease Fitting Included
----
Yes
No
----
Greaseable
----
Yes
No
----
Snap Rings Included
----
No
----
----
Washers Included
----
----
No
----
Belt Type
----
----
----
Serpentine
Pulley Diameter (in)
----
----
----
4-1/2 Inch
Voltage (V)
----
----
----
12 Volt
Number Of Outlets
1
----
----
----
Compressor Type
----
----
----
York-Diesel Kiki-Zexel-Seltec
Pulley Diameter (mm)
----
----
----
115mm
Air Tube Adaptable
No
----
----
----
Heat Shield Included
No
----
----
----
Grease Fitting Location
----
Cross
----
----
Pre-Greased
----
----
Yes
----
Gasket Or Seal Included
No
----
----
----
Heat Shield Material
Aluminized Steel
----
----
----
Castle Nut Included
----
----
No
----
Cotter Pin Included
----
----
No
----
Lock Nut Included
----
----
Yes
----
Lock Washer Included
----
----
No
----
Clamp Included
No
----
----
----
Number Of Inlets
1
----
----
----
Clutch Included
----
----
----
Yes
Installation Type
Direct-Fit
----
----
----
Model Number
----
----
----
DKS20
Hangers Included
No
----
----
----
Inlet Attachment Method
Bolt-On
----
----
----
Outlet Attachment Method
Bolt-On
----
----
----
Bearing Cap Diameter A (in)
----
1.690 Inch
----
----
Bearing Cap Diameter B (in)
----
1.690 Inch
----
----
Number Of Pulley Grooves
----
----
----
6
Exhaust Pipe Material
Stainless Steel
----
----
----
Catalytic Converter Body Material
Stainless Steel
----
----
----
Air Tube Pre-Installed
No
----
----
----
Bearing Cap Type A
----
High Wing Drilled
----
----
Bearing Cap Type B
----
High Wing Drilled
----
----
Adjusting Sleeve Included
----
----
No
----
Rod End Thread Gender
----
----
Male
----
Rack End Thread Gender
----
----
Female
----
Bearing Cap Diameter A (mm)
----
42.92mm
----
----
Bearing Cap Diameter B (mm)
----
42.92mm
----
----
Catalytic Converter Body Height (in)
5 Inch
----
----
----
Catalytic Converter Body Length (in)
6-1/4 Inch
----
----
----
Catalytic Converter Body Shape
Round
----
----
----
Catalytic Converter Body Width (in)
5 Inch
----
----
----
Ball Stud Type
----
----
Threaded
----
Ball Stud Housing Material
----
----
High Strength Steel
----
Ball Stud Bearing Material
----
----
Polymer
----
Tie Rod End Type
----
----
Inner
----
Catalytic Converter Body Height (mm)
127mm
----
----
----
Catalytic Converter Body Length (mm)
159mm
----
----
----
Catalytic Converter Body Width (mm)
127mm
----
----
----
Inlet Number 1 Inside Diameter (in)
2-1/2 Inch
----
----
----
Inlet Number 1 Inside Diameter (mm)
64mm
----
----
----
Outlet Number 1 Inside Diameter (in)
2-1/2 Inch
----
----
----
Outlet Number 1 Inside Diameter (mm)
64mm
----
----
----
Cap To Cap Length A (in)
----
4.500 Inch
----
----
Cap To Cap Length B (in)
----
4.500 Inch
----
----
Cap To Cap Length A (mm)
----
114.3mm
----
----
Cap To Cap Length B (mm)
----
114.3mm
----
----
Groove To Groove Length A - Internal Snap Ring (in)
----
5.530 Inch
----
----
Groove To Groove Length A - Internal Snap Ring (mm)
----
140.46mm
----
----
Groove To Groove Length B - Internal Snap Ring (in)
----
5.530 Inch
----
----
Groove To Groove Length B - Internal Snap Ring (mm)
----
140.46mm
----
----
Grease Fitting Type
----
Standard
----
----