Autolite Copper Core Spark Plug - 3922
GearWrench 1/4 Inch Combination Wrench - 81650
MasterPro Climate Control 10SE18 A/C Compressor - Remanufactured - 197353
MasterPro Chassis Tie Rod End - ES3581
Product
Attributes
Warranty
Oil Type
----
----
PAG 46
----
Seat
Gasket
----
----
----
Thread Size
M14-1.25
----
----
----
Type
----
Long Length Combination
----
----
Heat Range
11
----
----
----
Length (in)
----
5-1/16 Inch
----
----
New Or Remanufactured
----
----
Remanufactured
----
Hex Size (mm)
16mm
----
----
----
Dust Boot Included
----
----
----
Yes
Grease Fitting Included
----
----
----
Yes
Greaseable
----
----
----
Yes
Hex Size (in)
5/8 Inch
----
----
----
Washers Included
----
----
----
Yes
Belt Type
----
----
Serpentine
----
Pulley Diameter (in)
----
----
4-3/8 Inch
----
Wrench Size (in)
----
1/4 Inch
----
----
Voltage (V)
----
----
12 Volt
----
Compressor Type
----
----
Nippondenso
----
SAE Or Metric
----
SAE
----
----
Pulley Diameter (mm)
----
----
110mm
----
Number Of Points
----
12
----
----
Pre-Greased
----
----
----
Yes
Preset Gap (in)
0.030 Inch
----
----
----
Preset Gap (mm)
0.8mm
----
----
----
Thread Reach (in)
0.750 Inch
----
----
----
Castle Nut Included
----
----
----
No
Cotter Pin Included
----
----
----
Yes
Lock Nut Included
----
----
----
Yes
Lock Washer Included
----
----
----
No
Clutch Included
----
----
Yes
----
Model Number
----
----
10SE18
----
Dust Boot Color
----
----
----
Black
Number Of Pulley Grooves
----
----
6
----
Center Electrode Core Material
Nickel
----
----
----
Center Electrode Tip Material
Nickel
----
----
----
Approximate Resistor Value (Ohm)
4000 Ohm
----
----
----
Insulator Height (mm)
50.8mm
----
----
----
Adjusting Sleeve Included
----
----
----
No
Insulator Height (in)
1.999 Inch
----
----
----
Dust Boot Material
----
----
----
Neoprene
Ground Electrode Tip Material
Nickel
----
----
----
Thread Reach (mm)
19mm
----
----
----
Rod End Thread Gender
----
----
----
Male
Rack End Thread Gender
----
----
----
Female
End 1 Offset (Deg)
----
15 Degree
----
----
End 1 Thickness (in)
----
3/16 Inch
----
----
End 1 Width (in)
----
1/2 Inch
----
----
End 2 Offset (Deg)
----
15 Degree
----
----
End 2 Thickness (in)
----
3/16 Inch
----
----
End 2 Width (in)
----
7/16 Inch
----
----
End 1 Drive Type
----
Open End
----
----
Ball Stud Type
----
----
----
Threaded
Ball Stud Housing Material
----
----
----
High Strength Steel
Ball Stud Bearing Material
----
----
----
Polymer
Tie Rod End Type
----
----
----
Outer
Metallurgy
Copper
----
----
----